通過式清洗機的使用，采用不銹鋼鏈條輸送形式，通過式噴水清洗線。根據多種復雜工件的清洗、多孔、深孔特點，在清洗、干燥過程中設置低速旋轉，保證清洗、切水、隧道式烘干、防銹等要求采用鏈條穩定輸送形式，設計的通過式噴淋清洗烘干干線。

The use of through type cleaning machine adopts the form of stainless steel chain transportation and through type water spray cleaning line. According to the characteristics of cleaning, porous and deep holes of various complex workpieces, low-speed rotation is set in the process of cleaning and drying to ensure the requirements of cleaning, water cutting, tunnel drying and rust prevention. The chain stable conveying form is adopted, and the professionally designed through spray cleaning and drying trunk line is adopted.

對于一些特殊的清洗對象，還應配備熱空氣干燥過濾循環系統，專用清洗架(籃)和清洗液。通過式超聲波清洗機的主要功能，一是防止高光亮度物體的外貌受到損害，二是可以去除附著在外貌上的亞微米大小的顆粒。

For some special cleaning objects, hot air drying filtration circulation system, special cleaning rack (basket) and cleaning solution shall also be equipped. The main functions of the pass through ultrasonic cleaning machine are to prevent the appearance of high brightness objects from being damaged, and to remove submicron particles attached to the appearance.

浸在液體中，面向傳感器的一面可以被清洗，因此要停止兩面的清洗。經式清潔機操作注意事項： a、被清潔的部件應整齊地放置于輸送帶上，不得壓在滾輪上;被清潔的部件應放置在輸送帶上，不得堆疊過度，以免影響清潔效果。

When immersed in liquid, the side facing the sensor can be cleaned, so stop cleaning both sides. Precautions for the operation of the warp Cleaner: a. the cleaned parts shall be placed neatly on the conveyor belt and shall not be pressed on the roller; The cleaned parts shall be placed on the conveyor belt and shall not be stacked too much, so as not to affect the cleaning effect.

工作結束后，清洗過的部件不能停在運輸帶上，按下終止鍵，整個機器就停止運行了。清潔機采用不同的方法對包裝容器、包裝材料、包裝輔助材料、包裝件等進行清洗，達到預期的清潔級別。清洗液應定時加入水和一定比例的金屬清潔劑，以補償消耗，使液面保持在一定高度，如果清洗效果達不到常規技術要求，則應悉數更換清洗液。

After the work, the cleaned parts cannot stop on the conveyor belt. Press the stop key and the whole machine will stop running. The cleaning machine uses different methods to clean the packaging containers, packaging materials, packaging auxiliary materials and packaging parts, so as to achieve the expected cleaning level. Water and a certain proportion of metal cleaner shall be regularly added to the cleaning solution to compensate the consumption and keep the liquid level at a certain height. If the cleaning effect fails to meet the conventional technical requirements, all the cleaning solutions shall be replaced.

通過式清洗機清洗過程：自動上料→超聲清洗(拋動)→超聲精洗(拋動)→超聲漂洗(拋動)→超聲漂洗(拋動)→鼓泡漂洗(拋動)→鼓泡漂洗(拋動)→防銹漂洗(拋動)→熱風干燥→熱風干燥→自動下料。

Cleaning process of pass through cleaner: automatic feeding → ultrasonic cleaning (throwing) → ultrasonic fine cleaning (throwing) → ultrasonic rinsing (throwing) → ultrasonic rinsing (throwing) → bubbling rinsing (throwing) → bubbling rinsing (throwing) → antirust rinsing (throwing) → hot air drying → hot air drying → automatic feeding.

以上就是小編為您提供的關于超聲波清洗設備的知識，更多的精彩內容請您繼續關注我們的網站：http://fdcyxzx.com，我們會有更多對的精彩內容 為您分享.

The above is the knowledge about ultra ultrasonic cleaning equipment provided by Xiaobian. Please continue to pay attention to our website for more wonderful contents: http://fdcyxzx.com , we will have more wonderful content for you to share